Всем Доброго утра и Доброго дня!!! С Пятницей Нас!!!:)
Есть HiPath4000 V4.0,нужно установить плату STMI4.
В доке прочитал такую фразу:-"The time slots required by the HG 3500 boards in a half shelf must be nonblocking".
Означает ли эта фраза,что установив STMI4 в первый слот,слоты с 2 по 6 должны оставаться свободными!?

Нет.
Например у меня

ADDRESS : LTG 1 LTU 2 SOURCE GROUP 1 ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED | HW- | MODULE
PEN | MODULE | TYPE |ID |C|Y|NO | | MODULE |STATE INFO | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
1 | Q2324-X500 STMI4 1 A 0| | Q2324-X500 | 1 -11 - | READY
+--------------------------------+-+------------+------------+------------
| IP ADDRESS : xx. x. x. xx B-CHANNELS : 60 BCHLCNT : 60
| BLOCK NO : 9 PRERESERVED LINES ASSIGNED : NO
| 1. FUNCT : SIP 120 LINES B-CHANNELS : 60 BCHLCNT : 60
| SECURITY STATUS: 1:[ ] 2:[ ] 3:[ ] 4:[ ] 5:[ ] 6:[ ] 7:[ ] 8:[ ]
| (SEE BOTTOM) 9:[ ] 10:[ ] 11:[ ] 12:[ ] 13:[ ] 14:[ ] 15:[ ] 16:[ ]
+--------------------------------+-+------------+------------+------------
2 | Q2196-X DIU-N2 2 A 0| | Q2196-X | 1 -07 - | READY
3 | AVAILABLE 0| | AVAILABLE | |
4 | AVAILABLE 0| | AVAILABLE | |
5 | AVAILABLE 0| | AVAILABLE | |
6 | Q2225-X SLMAE A 0| | Q2225-X | 1 -07 - | READY
7 | Q2266-X LTUCA 0| | Q2266-X | 1 -14 - | READY
8 | AVAILABLE 0| | AVAILABLE | |
9 | AVAILABLE 0| | AVAILABLE | |
10 | AVAILABLE 0| | AVAILABLE | |
11 | AVAILABLE 0| | AVAILABLE | |
12 | AVAILABLE 0| | AVAILABLE | |
13 | AVAILABLE 0| | AVAILABLE | |
14 | Q2324-X500 STMI4 1 A 0| | Q2324-X500 | 1 -11 - | READY
+--------------------------------+-+------------+------------+------------
| IP ADDRESS : xx. x. x. xx B-CHANNELS : 60 BCHLCNT : 60
| BLOCK NO : 9 PRERESERVED LINES ASSIGNED : NO
| 1. FUNCT : SIP 120 LINES B-CHANNELS : 60 BCHLCNT : 60
| SECURITY STATUS: 1:[ ] 2:[ ] 3:[ ] 4:[ ] 5:[ ] 6:[ ] 7:[ ] 8:[ ]
| (SEE BOTTOM) 9:[ ] 10:[ ] 11:[ ] 12:[ ] 13:[ ] 14:[ ] 15:[ ] 16:[ ]
+--------------------------------+-+------------+------------+------------
Пока.
Олег.

А не влияет ли параметр "FUNCT" на резервирование тайм слотов,например если вот такой конфиг:
ADDRESS : LTG 1 LTU 1 SOURCE GROUP 1 ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED | HW- | MODULE
PEN | MODULE | TYPE |ID |C|Y|NO | | MODULE |STATE INFO | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
1 | Q2324-X510 STMI4 1 A 0| | Q2324-X510 | 1 -G1 - | READY
+--------------------------------+-+------------+------------+------------
| IP ADDRESS : 11. 0. 0. 1 B-CHANNELS : 120 BCHLCNT : 120
| BLOCK NO : 1 PRERESERVED LINES ASSIGNED : NO
| 1. FUNCT : HG3530 240 LINES B-CHANNELS : 120 BCHLCNT : 120
| SECURITY STATUS: 1:[ ] 2:[ ] 3:[ ] 4:[ ] 5:[ ] 6:[ ] 7:[ ] 8:[ ]
| (SEE BOTTOM) 9:[ ] 10:[ ] 11:[ ] 12:[ ] 13:[ ] 14:[ ] 15:[ ] 16:[ ]
+--------------------------------+-+------------+------------+------------

Раньше они были HFA, это я сейчас перепрограммировал на SIP.
Или вот другая рабочая полка


ADDRESS : LTG 1 LTU 1 SOURCE GROUP 1 ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED | HW- | MODULE
PEN | MODULE | TYPE |ID |C|Y|NO | | MODULE |STATE INFO | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
1 | Q2324-X500 STMI4 1 * A 0| | Q2324-X500 | 1 -11 - | READY
+--------------------------------+-+------------+------------+------------
| IP ADDRESS : xx. x. xx. xx B-CHANNELS : 60 BCHLCNT : 60
| BLOCK NO : 15 PRERESERVED LINES ASSIGNED : NO
| 1. FUNCT : HG3570 1 LINES B-CHANNELS : 35 BCHLCNT : 35
| 2. FUNCT : HG3530 100 LINES B-CHANNELS : 25 BCHLCNT : 25
| SECURITY STATUS: 1:[ ] 2:[ ] 3:[ ] 4:[ ] 5:[ ] 6:[ ] 7:[ ] 8:[ ]
| (SEE BOTTOM) 9:[ ] 10:[ ] 11:[ ] 12:[ ] 13:[ ] 14:[ ] 15:[ ] 16:[ ]
+--------------------------------+-+------------+------------+------------
2 | Q2196-X DIU-N2 1 A 0| | Q2196-X | 1 -07 - | READY
3 | AVAILABLE 0| | AVAILABLE | |
4 | AVAILABLE 0| | AVAILABLE | |
5 | AVAILABLE 0| | AVAILABLE | |
6 | AVAILABLE 0| | AVAILABLE | |
7 | Q2266-X LTUCA 0| | Q2266-X | 1 -14 - | READY
8 | AVAILABLE 0| | AVAILABLE | |
9 | AVAILABLE 0| | AVAILABLE | |
10 | AVAILABLE 0| | AVAILABLE | |
11 | AVAILABLE 0| | AVAILABLE | |
12 | AVAILABLE 0| | AVAILABLE | |
13 | AVAILABLE 0| | AVAILABLE | |
14 | Q2324-X500 STMI4 1 * A 0| | Q2324-X500 | 1 -11 - | READY
+--------------------------------+-+------------+------------+------------
| IP ADDRESS : xx. x. x. xx B-CHANNELS : 60 BCHLCNT : 60
| BLOCK NO : 15 PRERESERVED LINES ASSIGNED : NO
| 1. FUNCT : HG3570 1 LINES B-CHANNELS : 35 BCHLCNT : 35
| 2. FUNCT : HG3530 100 LINES B-CHANNELS : 25 BCHLCNT : 25
| SECURITY STATUS: 1:[ ] 2:[ ] 3:[ ] 4:[ ] 5:[ ] 6:[ ] 7:[ ] 8:[ ]
| (SEE BOTTOM) 9:[ ] 10:[ ] 11:[ ] 12:[ ] 13:[ ] 14:[ ] 15:[ ] 16:[ ]
+--------------------------------+-+------------+------------+------------
Пока.
Олег.
PS. Или я не совсем понял вопрос по функционалу...

Спасибо! Просто меня "смутила" фраза в документе.