Уважаемые коллеги.

Может быть кто-нибудь сталкивался с подобной проблемой и знает что делать.



После 2 дней работы в "новом" (найденном на дальнем складе бывшем в употреблении) 19” шасси SSC (NTDK20JA) ушел в постоянный рестарт.



System Controller

Pre-Boot: 03 dev2.37

Flash Boot: NTDK34FA_r11 dev2.54

Reset Reason: 80, 4 - Reset due to CP invoked reset

SRAM: 128 kBytes

DRAM: 32 MBytes, speed=60 ns

Security ID: 10297183 type: NT_STD

System ID: 10297183

Backup Flash: 1572 kBytes

Program Store: 48 MBytes

Flash Drive: 16 MBytes

Expansion board #1 not installed.

Expansion board #2 not installed.

Ethernet MAC address: 00:20:FFFFFFD8:D2:2D:2F

PCMCIA card installed in drive A.

PCMCIA card not installed in drive B.



*** To invoke install setup program from PCMCIA enter CONTROL-I ***



Executing power up self tests

Power up self test passed

DISKOS to be run.

Verifying Diskos.





*** OS RESTART ***





Communication Server 1000 Software

Release : x210450w

Created : Thu Jul 28 04:03:37 EDT 2005

Loaded : 24/5/10 17:39:01



Copyright(C) 1972-2004 Nortel Networks. All Rights Reserved.

VxWorks 5.2

Copyright(C) 1984-1997 Wind River Systems, Inc. All Rights Reserved.

Use of the above software subject to terms of a license agreement.

U.S. Government users subject to "Restricted Rights" under FAR & DFAR.



Exception: Vnum=2, PC=0x10157dac, Addr=0x200000, SSW=0x0505, Task="tStartup"(0x207373b8)



BUG7429 OS 0: ERROR "EXC in tExc". Restarting with code: 49



Warm Start begun - reason 49





*** OS RESTART ***





Communication Server 1000 Software

Release : x210450w

Created : Thu Jul 28 04:03:37 EDT 2005

Loaded : 0/0/00 0:00:00

Last Restart: 0/0/00 0:00:00

Current Time: 24/5/10 17:39:46



Copyright(C) 1972-2004 Nortel Networks. All Rights Reserved.

VxWorks 5.2

Copyright(C) 1984-1997 Wind River Systems, Inc. All Rights Reserved.



Exception: Vnum=2, PC=0x10157dac, Addr=0x200000, SSW=0x0505, Task="tStartup"(0x207373b8)



BUG7429 OS 0: ERROR "EXC in tExc". Restarting with code: 49



Warm Start begun - reason 49





*** OS RESTART ***





Communication Server 1000 Software

Release : x210450w

Created : Thu Jul 28 04:03:37 EDT 2005

Loaded : 0/0/00 0:00:00

Last Restart: 0/0/00 0:00:00

Current Time: 24/5/10 17:40:30



Copyright(C) 1972-2004 Nortel Networks. All Rights Reserved.

VxWorks 5.2

Copyright(C) 1984-1997 Wind River Systems, Inc. All Rights Reserved.



Exception: Vnum=2, PC=0x10157dac, Addr=0x200000, SSW=0x0505, Task="tStartup"(0x207373b8)



BUG7429 OS 0: ERROR "EXC in tExc". Restarting with code: 49



Warm Start begun - reason 49



Попытка переставить софт ничего не дала:



System Controller

Pre-Boot: 03 dev2.37

Flash Boot: NTDK34FA_r11 dev2.54

Reset Reason: 80, 4 - Reset due to CP invoked reset

SRAM: 128 kBytes

DRAM: 32 MBytes, speed=60 ns

Security ID: 10297183 type: NT_STD

System ID: 10297183

Backup Flash: 1572 kBytes

Program Store: 48 MBytes

Flash Drive: 16 MBytes

Expansion board #1 not installed.

Expansion board #2 not installed.

Ethernet MAC address: 00:20:FFFFFFD8:D2:2D:2F

PCMCIA card installed in drive A.

PCMCIA card not installed in drive B.



*** To invoke install setup program from PCMCIA enter CONTROL-I ***



Executing power up self tests

Power up self test passed

CONTROL-I entered. Invoking install setup program from SW Delivery Card.

DRAMOS load from SW Delivery Card successful.





*** OS RESTART ***





Communication Server 1000 Software

Release : x210450w

Created : Thu Jul 28 04:03:37 EDT 2005

Loaded : 24/5/10 12:11:31



Copyright(C) 1972-2004 Nortel Networks. All Rights Reserved.

VxWorks 5.2

Copyright(C) 1984-1997 Wind River Systems, Inc. All Rights Reserved.

Use of the above software subject to terms of a license agreement.

U.S. Government users subject to "Restricted Rights" under FAR & DFAR.



Exception: Vnum=2, PC=0x2085f638, Addr=0x200000, SSW=0x0505, Task="tStartup"(0x207373b8)



BUG7429 OS 0: ERROR "EXC in tExc". Restarting with code: 49



Warm Start begun - reason 49





*** OS RESTART ***





Communication Server 1000 Software

Release : x210450w

Created : Thu Jul 28 04:03:37 EDT 2005

Loaded : 0/0/00 0:00:00

Last Restart: 0/0/00 0:00:00

Current Time: 24/5/10 12:12:10



Copyright(C) 1972-2004 Nortel Networks. All Rights Reserved.

VxWorks 5.2

Copyright(C) 1984-1997 Wind River Systems, Inc. All Rights Reserved.



Exception: Vnum=2, PC=0x2085f638, Addr=0x200000, SSW=0x0505, Task="tStartup"(0x207373b8)



BUG7429 OS 0: ERROR "EXC in tExc". Restarting with code: 49



Warm Start begun - reason 49





Последнее, что написал CS в консоль которая была включена эти 2 дня было:



BERR705 EXC 0: Bus Error in Task "tTapeTask" (0x208127d0)

Warm Start begun - reason 49

--------------------------------------------------------------------------------

Problem Description

Fact:
core
Succession 3.0
Succession 4.0
Succession 4.5
Nortel Communication Server 1000S
1000S
Option 11c


Symptom:
Warm Start begun - reason 49
Deplist installation exceeds Z: drive space limit.
Z drive is full
Exception: Vnum=2, PC=0x10168a04, Addr=0x200000, SSW=0x0505, Task="tStartup"(0x207373b8)
BUG7429 OS 0: ERROR "EXC in tExc". Restarting with code: 49




Problem Resolution

Fix:
Install MPLR21001



Affected Products
Enterprise VoIP Core CS 1000S

Пардон.. Патч заменен на 21970, который входит в деплист. Он предотвращает копирование всех патчей на Z: при edd. В данной ситуации, видимо, надо загружаться с внешней флешки, заходить в PDT и тереть файлы патчей с диска Z:. Потом загружаться в штатном режиме и ставить свежий деплист.

С внешней не получается :( ..........

*** To invoke install setup program from PCMCIA enter CONTROL-I ***



Executing power up self tests

Power up self test passed

CONTROL-I entered. Invoking install setup program from SW Delivery Card.

DRAMOS load from SW Delivery Card successful.





*** OS RESTART ***





Communication Server 1000 Software

Release : x210450w

Created : Thu Jul 28 04:03:37 EDT 2005

Loaded : 24/5/10 12:11:31



Copyright(C) 1972-2004 Nortel Networks. All Rights Reserved.

VxWorks 5.2

Copyright(C) 1984-1997 Wind River Systems, Inc. All Rights Reserved.

Use of the above software subject to terms of a license agreement.

U.S. Government users subject to "Restricted Rights" under FAR & DFAR.



Exception: Vnum=2, PC=0x2085f638, Addr=0x200000, SSW=0x0505, Task="tStartup"(0x207373b8)



BUG7429 OS 0: ERROR "EXC in tExc". Restarting with code: 49



Warm Start begun - reason 49

Я делал по такому алгоритму:
1) Формат флешки через CTRL+B
2) Установка софта с дефолтной БД
3) Установка деплиста.
4) Накатывание старой БД.

Проблема таже в точности. Релиз тот же.
PDT - не доступен.
Формат флешки через CTRL+B - не помогает. Как можно потереть z: через FBUG?

Может я чего не так делаю :/

System Controller
Pre-Boot: 03 dev2.37
Flash Boot: NTDK34FA_r11 dev2.54
Reset Reason: 80, 4 - Reset due to CP invoked reset
SRAM: 128 kBytes
DRAM: 32 MBytes, speed=60 ns
Security ID: 10297183 type: NT_STD
System ID: 10297183
Backup Flash: 1572 kBytes
Program Store: 48 MBytes
Flash Drive: 16 MBytes
Expansion board #1 not installed.
Expansion board #2 not installed.
Ethernet MAC address: 00:20:FFFFFFD8:D2:2D:2F
PCMCIA card not installed in drive A.
PCMCIA card not installed in drive B.

*** To invoke install setup program from PCMCIA enter CONTROL-I ***

Executing power up self tests
Power up self test passed

Fbug680x0 Monitor/Debugger Version 3.0 - 27/1/98

FBUG> ct

SYSTEM TEST MENU
-------------------------------
Enter 'p' for Production test
or 'd' for Daughter board test
or 't' for Troubleshoot
or 's' for System power up test
Return key to exit

Enter selection: d

DAUGHTER BOARD TEST MENU
---------------------------------
0 - or return to EXIT MENU
1 - EXPN D/B 1
2 - EXPN D/B 2
3 - BACKWARDS COMPATIBLE D/B
4 - FLASH DAUGHTER BOARD

Enter selection: 4
Testing FLASH drive D/B
-Checking for previous data
-Flash d/b is not blank
Enter y to erase and test: y

Flash Drive device information
Device 0 AM29F032(32Mb,8bit wide)
start address = 1F000000 drive_size(bytes) = 1000000
-Reset device block 0
-Erasing device block 0
-Checking devices are erased
-Block 0 is erased
-ERASE PASSED
start_add=1F000000,stop_add=1FFFFFFC
.................................................. .................................................. ............................
-Erasing device block 0
-Checking devices are erased
-Block 0 is erased
-ERASE PASSED
PASS
Testing 48Mb FLASH on daughter board
-Checking for previous data
-Flash d/b is not blank
Enter y to erase and test: y

Flash Prog store device information
Device 0 Am29F016(16Mb,8bit wide)
start address=10000000 64k segs=20 seg_size=1000000
Device 1 Am29F016(16Mb,8bit wide)
start address=11000000 64k segs=20 seg_size=1000000
Device 2 Am29F016(16Mb,8bit wide)
start address=12000000 64k segs=20 seg_size=1000000
-Reset device block 0
-Reset device block 1
-Reset device block 2
-Erasing device block 0
-Erasing device block 1
-Erasing device block 2
-Checking devices are erased
-Block 0 1st bank is ERASED
-Block 1 1st bank is ERASED
-Block 2 1st bank is ERASED
-Block 2 2nd bank is ERASED
-Block 1 2nd bank is ERASED
-Block 0 2nd bank is ERASED
-ERASE PASSED
-Writing device block 0
start_add=10000000,bytes=1000000,stop_add=10FFFFFC
.................................................. .................................................. .................................................. .................................................. .................................................. ......-PASSED FLASH MEMORY TEST

-Writing device block 1
start_add=11000000,bytes=1000000,stop_add=11FFFFFC
.................................................. .................................................. .................................................. .................................................. .................................................. ......-PASSED FLASH MEMORY TEST

-Writing device block 2
start_add=12000000,bytes=1000000,stop_add=12FFFFFC
.................................................. .................................................. .................................................. .................................................. .................................................. ......-PASSED FLASH MEMORY TEST



-Reset device block 0
-Reset device block 1
-Reset device block 2
-Erasing device block 0
-Erasing device block 1
-Erasing device block 2
-Checking devices are erased
-Block 0 1st bank is ERASED
-Block 1 1st bank is ERASED
-Block 2 2nd bank is ERASED
-Block 2 1st bank is ERASED
-Block 1 2nd bank is ERASED
-Block 0 2nd bank is ERASED
-ERASE PASSED

PASS

SYSTEM TEST MENU
-------------------------------
Enter 'p' for Production test
or 'd' for Daughter board test
or 't' for Troubleshoot
or 's' for System power up test
Return key to exit

Enter selection:

FBUG>

System Controller
Pre-Boot: 03 dev2.37
Flash Boot: NTDK34FA_r11 dev2.54
Reset Reason: 80, 4 - Reset due to CP invoked reset
SRAM: 128 kBytes
DRAM: 32 MBytes, speed=60 ns
Security ID: 10297183 type: NT_STD
System ID: 10297183
Backup Flash: 1572 kBytes
Program Store: 48 MBytes
Flash Drive: 16 MBytes
Expansion board #1 not installed.
Expansion board #2 not installed.
Ethernet MAC address: 00:20:FFFFFFD8:D2:2D:2F
PCMCIA card installed in drive A.
PCMCIA card not installed in drive B.

*** To invoke install setup program from PCMCIA enter CONTROL-I ***

Executing power up self tests
Power up self test passed
CONTROL-I entered. Invoking install setup program from SW Delivery Card.
DRAMOS load from SW Delivery Card successful.


*** OS RESTART ***

Communication Server 1000 Software
Release : x210450w
Created : Thu Jul 28 04:03:37 EDT 2005
Loaded : 26/5/10 12:24:35

Copyright(C) 1972-2004 Nortel Networks. All Rights Reserved.
VxWorks 5.2
Copyright(C) 1984-1997 Wind River Systems, Inc. All Rights Reserved.
Use of the above software subject to terms of a license agreement.
U.S. Government users subject to "Restricted Rights" under FAR & DFAR.

BUG7429 OS 0: ERROR "EXC in tExc". Restarting with code: 49


Warm Start begun - reason 49

*** OS RESTART ***

мне такой манёвр предложили, но у меня
>> -Flash d/b is blank-ok to test <-----И вопросов не задаёт. потому и не помогло.




IF YOU HAVE THE PROBLEM, DIDN'T HAVE THE PATCH, AND NEED TO RECOVER
>> THE SYSTEM, FOLLOW THESE INSTRUCTIONS:
>> ----------------------------------

>> The root cause of the problem cannot be patched. So this MPLR limits
>> the size of "z:" drive to 1408 kbytes. Also it fixes a uncorrect
>> checks in the code which can cause INI with reason 33 in the case of
>> 1.5Mb "z:" drive.

>> If you encountered problem indicated by a BUG7429, invoke the
>> following
>> z: drive recovery process:

>> 1) Power off the system
>> 2) Power on the system
>> 3) Press key "ctrl B"
>> 4) Access to prompt FBUG>
>> 5) At the prompt FBUG> type the command ct

>> SYSTEM TEST MENU
>> -------------------------------
>> Enter 'p' for Production test
>> or 'd' for Daughter board test
>> or 't' for Troubleshoot
>> or 's' for System power up test
>> Return key to exit

>> Enter selection: t

>> TROUBLESHOOT TEST MENU
>> ---------------------------------
>> 0 - or return to EXIT MENU
>> 1 - LED
>> 2 - RTC
>> 4 - RAM TEST MENU
>> 5 - 020 TEST MENU
>> 6 - NETWORK TEST MENU
>> 7 - CONFERENCE TEST MENU
>> 8 - FLASH TEST MENU
>> 9 - FIBER D/B RS-232 LOOPBACK TEST MENU

>> - PROG DEVELOPMENT ONLY -
>> 50 - print I44-A31 address map
>> 51 - print important CSA variables
>> 99 - RESTA
>> RT BOOT

>> Enter selection: 8

>> ----- FLASH TEST MENU -----
>> 0 - EXIT TO MAIN T/S MENU
>> 1 - ALL TESTS
>> 2 - W/R TEST FLASH ALT BOOT
>> 3 - W/R TEST FLASH DRIVE
>> 4 - W/R TEST FLASH PROG STORE
>> 5 - ERASE FLASH ALT BOOT MAIN CAB
>> 6 - ERASE FLASH DRIVE ON DB
>> 7 - ERASE FLASH PROG STORE ON DB

>> Enter selection: 1
>> Testing 2Mb FLASH ALTBOOT on main board Testing Id check
Manufacture ID ->>> 10001
Device ID ->>> 22AB22AB
>> Erasing
>> Writing
>> maxtrys=5
>> Erasing
>> PASS
>> Te
>> sting FLASH drive D/B
>> -Checking for previous data
>> -Flash d/b is not blank
>> Enter y to erase and test: n <--- Enter n !!!!!!!
>> FAIL

>> Power off then on the system
>> 9) The system will be loaded but no z drive in devs
>> 10) Install the mplr21970 on the ssc switch

Уважаемые коллеги!
Огромное спасибо
Все получилось, после выполнения процедуры рекомендованной многоуважаемым MarksmaN.

подскажите, как Deplists_SSC_X21_04_50W.zip через PDT распокавать, переместить, запустить... в общем как это делается?

подскажите, как Deplists_SSC_X21_04_50W.zip через PDT распокавать, переместить, запустить... в общем как это делается?

Это делается через 143 ovly, команда mdp

ДА самый простой путь:
1. записать этот файл (Deplists_SSC_X21_04_50W.zip) на PCMCI'ную карту(например в корень)
2. Вставить в один из слотов в морде (например в а:) эту карту
3. Затем в LD 143 сказать:
.mdp install a:/Deplists_SSC_X21_04_50W.zip
далее по смыслу ........

можно также распаковать этот архив, переместить (например по FTP) их на z а далее http://bbs.radiolink.ru/forum/showthread.php?t=19430&highlight=pload

ДА самый простой путь:
1. записать этот файл (Deplists_SSC_X21_04_50W.zip) на PCMCI'ную карту(например в корень)
2. Вставить в один из слотов в морде (например в а:) эту карту
3. Затем в LD 143 сказать:
.mdp install a:/Deplists_SSC_X21_04_50W.zip
далее по смыслу ........

можно также распаковать этот архив, переместить (например по FTP) их на z а далее http://bbs.radiolink.ru/forum/showthread.php?t=19430&highlight=pload

Только не забыть перед всем этим сократить имя файла до 8 символов ;)

спасибо не мне, а учителю моему из Белтела! жаль что мне не помогло.

Коллеги столкнулся с аналогичной проблемой.

Циклическая перезагрузка по 49 причине.

Флешку отформатировал, попробывал перезалить софт, но после загрузки с флешки DRAMOS проблема повторяется.

То есть имею процессор с пустой флешкой на которую невозможно залить софт.

Как побороть проблему?

Спасибо!