Необходимо переключить модемный пул Lucent MAX с сигнализации R2D на EDSS. После конфигурирования каналы в исходном. Попытка совершить знадок ругается на сообщение SETUP что неверный состав параметров.
Кто знает какой должен быть формат???
Rx2 TS 27 NEW CALL CR=25 567916506->9 11:47:53-11:47:53
11:47:53.622 Rx2 TS 27 SETUP
02 01 00 00 08 02 00 19 05 04 03 90 90 A3 18 03 AB 83 9B 6C 0B 21 83 35 36 37 39 31 36 35 30 36
70 02 C1 39
LAYER 2
LAYER 3
04 08 00001000 Protocol discriminator.......... User-network call control message
05 02 0000.... Filler.......................... 0 Dec
....0010 Length of call reference value.. 2 Dec (15 Bit CRV)
06 00 0....... Call reference flag............. From origination
.0000000 Call reference value............ See below
07 19 00011001 Call reference value............ 25 Dec
08 05 00000101 Message type.................... SETUP
-- Bearer capability
09 04 00000100 Information element ID.......... Bearer capability
10 03 00000011 Length.......................... 3 Dec
11 90 1....... Extension....................... Last octet
.00..... Coding standard................. ITU-T
...10000 Info. transfer capability....... 3.1 kHz audio
12 90 1....... Extension....................... Last octet
.00..... Transfer mode................... Circuit mode
...10000 Information transfer rate....... 64 kbit/s
13 A3 1....... Extension....................... Last octet
.01..... Layer ID........................ Layer 1
...00011 User info. layer 1 protocol..... Rec. G.711 A-law
-- Channel identification
14 18 00011000 Information element ID.......... Channel identification
15 03 00000011 Length.......................... 3 Dec
16 AB 1....... Extension....................... Last octet
.0...... Interface ident. present........ Implicitly identified
..1..... Interface type.................. Primary rate
...0.... Spare........................... 0 Dec
....1... Preferred/Exclusive............. Channel is exclusive
.....0.. D-channel indicator............. not D-channel
......11 Information channel selection... Any channel
17 83 1....... Extension....................... Last octet
.00..... Coding standard................. CCITT
...0.... Number/map...................... Indicated by the number
....0011 Channel/map element type........ B-channel units
18 9B 1....... Extension....................... Last octet
.00..... Spare........................... 0 Dec
...11011 Timeslot number................. 27 Dec
-- Calling party number
19 6C 01101100 Information element ID.......... Calling party number
20 0B 00001011 Length.......................... 11 Dec
21 21 0....... Extension....................... Continuation
.010.... Type of number.................. National number
....0001 Numbering plan.................. ISDN/telephony numbering plan
22 83 1....... Extension....................... Last octet
.00..... Presentation indicator.......... Presentation allowed
...000.. Spare........................... 0 Dec
......11 Screening indicator............. Network provided
23 35 - 31 Address signal.................. 567916506
-- Called party number
32 70 01110000 Information element ID.......... Called party number
33 02 00000010 Length.......................... 2 Dec
34 C1 1....... Extension....................... Last octet
.100.... Type of number.................. Subscriber number
....0001 Numbering plan.................. ISDN/telephony numbering plan
35 39 - 35 Address signal.................. 9
11:47:53.625 Rx1 RR (receive ready)
11:47:53.629 Rx1 TS 27 RELEASE COMPLETE
00 01 00 02 08 02 80 19 5A 08 03 80 E4 18
LAYER 2
LAYER 3
04 08 00001000 Protocol discriminator.......... User-network call control message
05 02 0000.... Filler.......................... 0 Dec
....0010 Length of call reference value.. 2 Dec (15 Bit CRV)
06 80 1....... Call reference flag............. From destination
.0000000 Call reference value............ See below
07 19 00011001 Call reference value............ 25 Dec
08 5A 01011010 Message type.................... RELEASE COMPLETE
-- Cause
09 08 00001000 Information element ID.......... Cause
10 03 00000011 Length.......................... 3 Dec
11 80 1....... Extension....................... Last octet
.00..... Coding standard................. CCITT
...0.... Spare........................... 0 Dec
....0000 Location........................ User
12 E4 1....... Extension....................... Last octet
.1100100 Cause value..................... Invalid information element contents
Rx2 TS 27 END CALL CR=25 567916506->9 11:47:53-11:47:53
Type of number и Numbering plan можно попробовать сменить на Unknown
Анализатор не расшифровал элемент на который ругается.
11:43:15.127 Rx1 TS 18 RELEASE COMPLETE
00 01 00 02 08 02 80 10 5A 08 03 80 E4 18
LAYER 2
LAYER 3
04 08 00001000 Protocol discriminator.......... User-network call control message
05 02 0000.... Filler.......................... 0 Dec
....0010 Length of call reference value.. 2 Dec (15 Bit CRV)
06 80 1....... Call reference flag............. From destination
.0000000 Call reference value............ See below
07 10 00010000 Call reference value............ 16 Dec
08 5A 01011010 Message type.................... RELEASE COMPLETE
-- Cause
09 08 00001000 Information element ID.......... Cause
10 03 00000011 Length.......................... 3 Dec
11 80 1....... Extension....................... Last octet
.00..... Coding standard................. CCITT
...0.... Spare........................... 0 Dec
....0000 Location........................ User
12 E4 1....... Extension....................... Last octet
.1100100 Cause value..................... Invalid information element contents
Т.е последний байт не расшифровал (код 18 - Channel identification)
Только что не нравится не понятно?
-- Channel identification
14 18 00011000 Information element ID.......... Channel identification
15 03 00000011 Length.......................... 3 Dec
16 AB 1....... Extension....................... Last octet
.0...... Interface ident. present........ Implicitly identified
..1..... Interface type.................. Primary rate
...0.... Spare........................... 0 Dec
....1... Preferred/Exclusive............. Channel is exclusive
.....0.. D-channel indicator............. not D-channel
......11 Information channel selection... Any channel
17 83 1....... Extension....................... Last octet
.00..... Coding standard................. CCITT
...0.... Number/map...................... Indicated by the number
....0011 Channel/map element type........ B-channel units
18 92 1....... Extension....................... Last octet
.00..... Spare........................... 0 Dec
...10010 Timeslot number................. 18 Dec
Вродебы всё законно.
:confused:
Всё справился
Неверное значение
11 Information channel selection... Any channel
Исправил, заработало