swop
12.05.2006, 19:09
Уважаемые Коллеги!
Помогите с решенем проблемы, пытаюсь соединить две станции TD500 через IP канал, схема такова:
сторона А | сторора Б
PBX1 -E1- 2811 --IP-- 2811 -E1- PBX2
конфигурация 2811(А)
isdn switch-type primary-net5
controller E1 0/1/0
clock source internal
pri-group timeslots 1-16
interface Serial0/1/0:15
isdn switch-type primary-net5
isdn protocol-emulate network
isdn incoming-voice voice
voice-port 0/1/0:15
cptone RU
bearer-cap Speech
dial-peer voice 1 voip
destination-pattern 4...
session protocol sipv2
session target ipv4:192.168.15.254
!
dial-peer voice 2 pots
destination-pattern 3...
forward-digits all
port 0/1/0:15
конфигурация 2811(Б)
isdn switch-type primary-net5
controller E1 0/1/1
clock source internal
pri-group timeslots 1-16
interface Serial0/1/1:15
isdn switch-type primary-net5
isdn protocol-emulate network
isdn incoming-voice voice
voice-port 0/1/1:15
cptone RU
bearer-cap Speech
dial-peer voice 1 voip
destination-pattern 3...
session protocol sipv2
session target ipv4:172.20.16.1
!
dial-peer voice 2 pots
destination-pattern 4...
forward-digits all
port 0/1/1:15
------------------------------------------------------------
На обоих станциях TD500 настроены tie-line следующим образом
TD500 (A)
8.1 Tie-Routing table
PBX Code 3
num lead digit digit to delete num add trunk grp
1 4 0 0 2
TD500 (Б)
8.1 Tie-Routing table
PBX Code 4
num lead digit digit to delete num add trunk grp
10 3 0 0 10
------------------------------------------------------------
При попытке звонка со стороны А на телефон стороны Б на маршрутизаторе 2811 (Б) в логе с debug q931 видно следующее
008162: .May 12 10:38:05.881: ISDN Se0/1/1:15 Q931: TX -> SETUP pd = 8 callref = 0x00C1
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Calling Party Number i = 0x0180, '3416'
Plan:ISDN, Type:Unknown
Called Party Number i = 0x81, '4105'
Plan:ISDN, Type:Unknown
008163: .May 12 10:38:06.013: ISDN Se0/1/1:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0x80C1
008164: .May 12 10:38:21.029: ISDN Se0/1/1:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x80C1
Cause i = 0x819C - Invalid number format (incomplete number)
Any ideas? Спасибо за внимание!
Помогите с решенем проблемы, пытаюсь соединить две станции TD500 через IP канал, схема такова:
сторона А | сторора Б
PBX1 -E1- 2811 --IP-- 2811 -E1- PBX2
конфигурация 2811(А)
isdn switch-type primary-net5
controller E1 0/1/0
clock source internal
pri-group timeslots 1-16
interface Serial0/1/0:15
isdn switch-type primary-net5
isdn protocol-emulate network
isdn incoming-voice voice
voice-port 0/1/0:15
cptone RU
bearer-cap Speech
dial-peer voice 1 voip
destination-pattern 4...
session protocol sipv2
session target ipv4:192.168.15.254
!
dial-peer voice 2 pots
destination-pattern 3...
forward-digits all
port 0/1/0:15
конфигурация 2811(Б)
isdn switch-type primary-net5
controller E1 0/1/1
clock source internal
pri-group timeslots 1-16
interface Serial0/1/1:15
isdn switch-type primary-net5
isdn protocol-emulate network
isdn incoming-voice voice
voice-port 0/1/1:15
cptone RU
bearer-cap Speech
dial-peer voice 1 voip
destination-pattern 3...
session protocol sipv2
session target ipv4:172.20.16.1
!
dial-peer voice 2 pots
destination-pattern 4...
forward-digits all
port 0/1/1:15
------------------------------------------------------------
На обоих станциях TD500 настроены tie-line следующим образом
TD500 (A)
8.1 Tie-Routing table
PBX Code 3
num lead digit digit to delete num add trunk grp
1 4 0 0 2
TD500 (Б)
8.1 Tie-Routing table
PBX Code 4
num lead digit digit to delete num add trunk grp
10 3 0 0 10
------------------------------------------------------------
При попытке звонка со стороны А на телефон стороны Б на маршрутизаторе 2811 (Б) в логе с debug q931 видно следующее
008162: .May 12 10:38:05.881: ISDN Se0/1/1:15 Q931: TX -> SETUP pd = 8 callref = 0x00C1
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Calling Party Number i = 0x0180, '3416'
Plan:ISDN, Type:Unknown
Called Party Number i = 0x81, '4105'
Plan:ISDN, Type:Unknown
008163: .May 12 10:38:06.013: ISDN Se0/1/1:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0x80C1
008164: .May 12 10:38:21.029: ISDN Se0/1/1:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x80C1
Cause i = 0x819C - Invalid number format (incomplete number)
Any ideas? Спасибо за внимание!